If you've filled the same pothole twice and it came back, you're not alone — and you're also doing it wrong. Most gravel driveway repairs fail not because of bad materials, but because the repair only addresses the hole and not the reason the hole exists. This guide covers how to actually fix the three most common gravel driveway problems: potholes that keep returning, ruts from vehicle traffic, and washouts from drainage issues.
Why potholes keep coming back
The reason a pothole returns after you fill it is almost always the same: the base material underneath has softened, and you filled the hole without addressing the base. Here's what's actually happening beneath the surface.
When a vehicle repeatedly drives over the same spot, it compresses the stone and soil below. Over time, that compressed material forms a bowl shape — the center is densest, but the edges are loose and crumbling. Rain water collects in the bowl, saturates the base, and the next vehicle load pushes everything down further. Every time you dump new stone in and drive over it, you're just adding to the bowl rather than fixing the structure underneath it.
The most common mistake: Filling potholes with new gravel and immediately driving over them. This compresses the fresh stone into the same soft spot and the hole reappears within weeks. You have to address the base first.
How to fix a pothole (that actually stays fixed)
This takes more work than just dumping stone in, but it's a one-time fix rather than an annual repeat.
-
1Dig it out completely Use a pointed shovel or mattock to remove all loose material from the pothole, going down until you hit firm, undisturbed ground. Don't just scrape the surface — you need to get below the saturated, compacted layer. This usually means digging 6–12 inches deeper than the bottom of the visible hole.
-
2Break up the compacted sidewalls The sides of a pothole are almost always compacted and slightly glazed from repeated compression. Use a pick or the corner of a mattock to break them up and create a rough, irregular edge. This gives the new material something to key into rather than sitting in a smooth bowl.
-
3Extend the repair zone 12–24 inches around the hole The material immediately surrounding a pothole is almost always compromised even if it looks fine. Rake out the gravel around the hole in a 12–24 inch ring, down to base level. This prevents the repair from sinking at its edges and creating two smaller potholes where one used to be.
-
4Fill in 2–3 inch layers, tamping each one Start with coarse base material (#57 crushed stone) and fill in 2–3 inch lifts. Tamp each layer firmly before adding the next — use a hand tamper for smaller holes, a plate compactor for anything bigger than about 12 inches across. Adding 6 inches of stone all at once and tamping the top doesn't compact the middle layers.
-
5Slightly overfill and crown the surface Fill the final layer 1–2 inches above the surrounding surface and shape a slight crown. It will compact down to grade with normal traffic over the next week or two. If you fill exactly flush, it will settle low and collect water again.
Best material for pothole repair: #411 crusher run (a blend of crushed stone and stone dust) compacts better than pure #57 and holds its shape with less settling. For the base, use #57 or #53 — angular crushed stone, not rounded pea gravel, which doesn't lock together.
Fixing ruts
Ruts are long depressions that form along the tire track lines, usually from repeated passes in the same spot during wet conditions. Unlike potholes, ruts indicate a problem along the entire wheel path — not just one spot — so the fix is different.
Why ruts form
Ruts happen when the base underneath the tire track is soft enough to compress under load. This is almost always a combination of two factors: too little base depth for the traffic it's carrying, and water sitting in the base layer. Thin driveways (3–4 inches) rut quickly. Driveways over clay with poor drainage rut even in dry conditions if the clay is shallow.
Light rutting (under 2 inches deep)
If ruts are shallow and the base material is still firm when you probe it, surface regrading often works. Rake the high areas (the crown between tire tracks, the edges) down into the ruts, then add fresh #411 crusher run as needed to bring everything level. Run a water-filled lawn roller or vehicle traffic over the regraded area to help it compact. This is a maintenance fix, not a permanent structural repair, but it extends the life of the surface between more significant work.
Deep or recurring ruts
Ruts deeper than 2–3 inches, or ruts that came back after surface regrading, indicate base failure. The fix involves:
- Removing all existing surface material along the rutted section down to undisturbed subgrade
- Checking the subgrade for soft spots — probe with a rod; if it sinks easily, the subgrade needs to dry out before repair (or you need to address drainage first)
- If subgrade is wet clay: consider installing a layer of geotextile fabric before rebuilding the base — it prevents stone from mixing into the clay and dramatically increases base life
- Rebuilding with 4–6 inches of compacted base stone (#57), then 2 inches of surface material
Fixing washouts
Washouts happen when water moves fast enough across or down the driveway surface to carry gravel with it. They're common on sloped driveways after heavy rain, at the base of hills where runoff concentrates, and anywhere a culvert is undersized or clogged. Filling the washout without fixing the water flow just means you'll fill it again after the next storm.
Step 1: Find where the water is coming from
Walk your driveway during or right after a heavy rain if you can safely do so. Look for where water is concentrating and flowing across the surface. Common sources: roadside ditches that overflow onto the driveway, slopes on either side that drain onto the surface, clogged culverts that back up water, and low points that collect runoff from the surrounding yard.
Step 2: Address the drainage first
Refill the washout area, but also fix the water problem. Depending on what you find:
- Clogged culvert: Clear it first — a garden hoe and some physical work usually does it. If the culvert itself is collapsed or undersized, it needs replacing before any surface work makes sense
- Sheet flow across surface: Regrade the edges of the driveway to encourage water to sheet off the side rather than flow down the middle. A 2–4% cross-slope (about a 1-inch drop per 4 feet of width) is the target
- Concentrated flow at the base of a slope: Install a stone-lined channel or French drain to intercept runoff before it hits the driveway, or add a water bar (a shallow angled channel cut across the driveway) to divert flow off the edge before it accelerates
Step 3: Fill the washout properly
Once water flow is addressed, fill washouts the same way as potholes — in layers, tamped, with coarse base stone first and surface material on top. For large washouts on a slope, slightly larger angular base stone (#2 or #3 crushed) holds better on grades than #57.
When to top-dress the whole driveway
Gravel driveways lose material over time — it migrates to the edges, gets pushed into the lawn, or gets picked up on vehicle tires. When your surface looks thin, patchy, or when potholes and ruts are appearing in multiple spots at once, it's time for a full top-dress rather than spot repairs.
| Sign | Likely Cause | Fix |
|---|---|---|
| Multiple potholes across driveway | Surface layer worn through | Top-dress with 1–2" of #411 |
| Can see tire tracks in dirt underneath | Surface completely worn | Top-dress with 2–3" of #411 |
| Stone accumulated at edges only | Normal migration, needs redistribution | Regrade edges back to center first, then top-dress lightly |
| Soft spots in multiple areas | Base failure, likely drainage issue | Address drainage, rebuild base, then surface |
| Ruts forming in warm weather | Base too thin for traffic load | Remove surface, add base stone, rebuild |
A typical top-dress for a 20×40 ft driveway needs 4–8 tons of surface material, depending on how much has been lost. Use the gravel calculator with your driveway dimensions and a 1–2 inch depth to estimate your order.
What you'll need for repairs
For small repairs — one or two potholes — you may be able to pick up a few bags of crusher run from a local home center. But for anything more than spot fixes, ordering bulk material by the ton from a local quarry or aggregate supplier is significantly cheaper per pound and the quality is better. Aggregate Markets is worth checking to see local delivered prices if you need more than a ton — it compares suppliers by zip code so you're not calling around blindly.
How often does a gravel driveway need maintenance?
A well-built gravel driveway over a solid base needs a light top-dress every 2–3 years and annual inspection of drainage. Heavy-use driveways — daily truck traffic, steep slopes, clay soil — need attention more often. The biggest factor in long-term maintenance cost isn't the quality of the gravel you buy; it's whether the drainage was designed correctly when the driveway was built. A driveway that sheds water properly can go 5+ years between significant maintenance.
For a full breakdown of what a proper new installation looks like, see the driveway install guide — it covers base preparation, drainage design, and material selection in detail.