The short answer: a standard two-car driveway (20ร—40 ft) at 6" depth needs roughly 18 tons of gravel. But the actual number for your project depends on your driveway size, the depth you're installing, and whether you're doing a base layer, surface layer, or both. This guide walks through the math so you order the right amount โ€” not 30% too much or too little.

Skip the math โ€” use the calculator

Enter your driveway length, width, and depth. Get tons and cubic yards instantly.

Calculate My Driveway โ†’

The formula (if you want to do it by hand)

Tons = (Length ร— Width ร— Depth in inches รท 12) รท 27 ร— 1.4
Divide by 27 to convert cubic feet to cubic yards. Multiply by 1.4 to convert cubic yards to tons (standard crushed stone density). Add 10% for waste and compaction.

Example: 20 ft wide ร— 40 ft long ร— 6 inches deep

= (20 ร— 40 ร— 6 รท 12) รท 27 ร— 1.4
= (400 cu ft) รท 27 ร— 1.4
= 14.8 cu yd ร— 1.4
= 20.7 tons (before adding 10% buffer = ~23 tons to order)

Always order 10% more than your calculation. Compaction settles the stone 10โ€“15% from its loose volume, and you'll spill some at the edges during spreading. Running short mid-project and waiting for a second delivery is worse than having a small pile left over.

Quick reference table by driveway size

These figures are for a 6" total depth (4" base + 2" surface) โ€” the minimum recommended for passenger vehicle driveways. Stone density assumed at 1.4 tons per cubic yard for #57 and #411 blended.

Driveway SizeSq FtCubic YardsTons NeededOrder This Much
Single car, short (10ร—20 ft)2003.75.26 tons
Single car (12ร—40 ft)4808.912.414 tons
Single car, long (12ร—60 ft)72013.318.721 tons
Two car (20ร—30 ft)60011.115.517 tons
Two car, standard (20ร—40 ft)80014.820.723 tons
Two car, long (20ร—60 ft)1,20022.231.134 tons
Country drive (12ร—150 ft)1,80033.346.751 tons
Country drive (12ร—300 ft)3,60066.793.3103 tons

Depth matters more than people think

Most homeowners underestimate how much depth changes tonnage. Going from 4" to 6" increases your order by 50%. Going from 6" to 8" adds another 33%. Here's how depth affects a standard 20ร—40 ft driveway:

DepthSuitable ForTons (20ร—40 ft)Approx. Cost (at $50/ton)
3โ€“4 inchesTop-dressing an existing base only8โ€“11 tons$400โ€“$550
5โ€“6 inchesNew driveway, passenger vehicles14โ€“20 tons$700โ€“$1,000
7โ€“8 inchesNew driveway, light trucks / SUVs21โ€“27 tons$1,050โ€“$1,350
10โ€“12 inchesHeavy vehicles, farm equipment28โ€“33 tons$1,400โ€“$1,650

The minimum for a new driveway that handles daily passenger car traffic is 6 inches total โ€” 4" of base stone and 2" of surface stone. Installing less might look fine for the first season, but thin driveways rut quickly under regular use.

Base stone vs. surface stone โ€” they're ordered separately

A proper two-layer driveway uses two different materials in different quantities. You don't just order "gravel" โ€” you order two types:

LayerMaterialDepthPurpose
Base#57 crushed stone4"Load bearing, drainage
Surface#411 crusher run2"Firm driving surface

For a 20ร—40 ft driveway: the base layer (4") needs about 15 tons of #57, and the surface layer (2") needs about 7 tons of #411. Total: 22 tons across two orders. Use the calculator for each layer separately โ€” enter the same length and width but change the depth for each.

How many truckloads is that?

Standard aggregate delivery trucks carry 12โ€“15 tons per load. A few quick calculations:

Project SizeTons NeededTruck Loads
Single car driveway (4" top-dress)6โ€“8 tons1 load
Single car driveway (6" new install)14 tons1 load
Two-car driveway (6" new install)23 tons2 loads
Two-car driveway (8" new install)31 tons2โ€“3 loads
150-ft country driveway (6" new)51 tons4 loads

Each delivery costs $50โ€“$200 depending on distance, so ordering two stone types in the same call โ€” or scheduling both loads in one day โ€” saves on delivery fees.

What changes the density number?

The 1.4 tons/cubic yard figure used above is accurate for most crushed limestone and granite. But different stone types have different densities โ€” which means the same volume weighs different amounts. This matters when you're comparing quotes priced per ton vs. per cubic yard:

Stone TypeApprox. Density (tons/cu yd)Notes
#57 Crushed Limestone1.35โ€“1.45Most common base stone
#411 Crusher Run1.45โ€“1.55Denser due to fines content
Pea Gravel1.2โ€“1.35Lighter, rounder particles
Recycled Concrete1.4โ€“1.5Variable, depends on source
Caliche / Decomposed Granite1.3โ€“1.5Regional variation is high

When a quarry quotes you per cubic yard, use their delivered density to convert to tons (or ask them directly how many tons per yard for that specific material). Quotes in tons are easier to compare across suppliers.

Ready to order?

Once you have your tonnage, the next step is finding out what delivery actually costs from local suppliers โ€” prices vary more by location than most people expect. Aggregate Markets lets you put in your address and get real delivered prices from quarries near you, which is faster than calling four suppliers individually and trying to compare apples to apples.

For the full installation process once your material is ordered, see the driveway installation guide โ€” it covers site prep, compaction, and how to build a driveway that doesn't need repairs every spring.